Duplex stainless steel / MATERIAL REFERENCE
Hot-rolled lean duplex material enquiries using the Chinese S22152 designation, with the current S20013 naming reference and a qualified comparison to UNS S32001.
HOT-ROLLED COIL, SHEET & PLATE
Sheye supplies this material as hot-rolled flat products. Confirm the required dimensions, heat treatment, surface and inspection basis for your order. Cold-rolled comparison values below are identified separately.
Compare the exact designation, chemical limits and test conditions before specifying material. Related grades are not automatically interchangeable or certified to all four standards.
EN 10028-7
Cast-analysis composition and solution-annealed, room-temperature flat-product properties. Sheye supply enquiries cover hot-rolled coil, sheet and plate; available dimensions are confirmed for each order.
Reference: 2016; current DIN EN10028-7:2016-10, checked2026-09-09Related-grade / reference qualifications applyASTM A240/A240M
Plate, sheet and strip for pressure vessels and general applications. Flat-product reference data; not bar/profile specifications or guaranteed Sheye stock capability.
Reference: A240/A240M-20aSpecification confirmation requiredS22152 is a Chinese designation; it must not be labeled UNS S22152. No exact S22152 row was found in ASTM A240/A240M-20a. The linked primary research identifies Chinese S22152 as associated with UNS S32001; this supports a related reference, not automatic dual certification. The complete UNS S32001 reference is provided as a clearly labeled variant for technical comparison. For an ASTM order, specify UNS S32001 and verify the complete chemistry, mechanical properties, delivery condition and contractual edition. No S22152-specific ASTM numeric limits are invented or inferred from the UNS number.
JIS G 4305
Cold-rolled stainless steel plate, sheet and strip. The requested Sheye additions are hot-rolled; JIS G4304 applicability must be treated separately.
Reference: 2021; current JSSA and Nippon Steel 2026 reference summariesSpecification confirmation requiredS22152 is a Chinese numerical designation related to UNS S32001 in GB/T 3280-2015; it is not a verified Japanese designation or a separately established UNS number. This means the direct correspondence is unverified, not a claim that no contractual Japanese specification can ever be agreed. JIS G4305 covers cold-rolled flat products. JIS G4304 is the separate hot-rolled flat-product standard; its scope alone does not establish grade coverage or numerical acceptance limits. Do not relabel SUS821L1, SUS323L or SUS329J3L as this grade merely because each is a duplex stainless steel.
GB/T 3280
Cold-rolled stainless steel plate, sheet and strip. Numerical values below are cold-rolled references; they are not acceptance limits for the hot-rolled products offered on this page.
Reference: 2015Mass %. ≤ means maximum; ≥ means minimum. A range includes both limits. “—” means no value published in this comparison; it never means zero.
Scroll the table horizontally to compare all standards.
| Element | EN 10028-72016; current DIN EN10028-7:2016-10, checked2026-09-09 | ASTM A240/A240MA240/A240M-20a | JIS G 43052021; current JSSA and Nippon Steel 2026 reference summaries | GB/T 32802015 |
|---|---|---|---|---|
| Designation | 1.4482 / X2CrMnNiMoN21-5-3 — comparison reference for the Chinese S22152 designation | UNS S32001 — related ASTM reference for Chinese S22152; requires independent compliance confirmation | No direct JIS counterpart verified | 022Cr21Mn5Ni2N / S22152 (Chinese designation, GB/T 3280-2015) |
| C | ≤0.030 | ≤0.030 | — | ≤0.030 |
| Si | ≤1.00 | ≤1.00 | — | ≤1.00 |
| Mn | 4.0–6.0 | 4.00–6.00 | — | 4.00–6.00 |
| P | ≤0.035 | ≤0.040 | — | ≤0.040 |
| S | ≤0.030 | ≤0.030 | — | ≤0.030 |
| Cr | 19.5–21.5 | 19.5–21.5 | — | 19.50–21.50 |
| Ni | 1.50–3.50 | 1.00–3.00 | — | 1.00–3.00 |
| Mo | 0.10–0.60 | ≤0.60 | — | ≤0.60 |
| N | 0.05–0.20 | 0.05–0.17 | — | 0.05–0.17 |
| Cu | ≤1.00 | ≤1.00 | — | ≤1.00 |
Rp0.2 is 0.2% proof strength; Rm is tensile strength; A is elongation. The delivery condition, product form, thickness and specimen basis belong to the value. Rows identify the reference specification or manufacturer summary and its qualifications; values are not design allowables.
| Standard / designation | Condition & thickness | Rp0.2 | Rm | Elongation | Hardness |
|---|---|---|---|---|---|
| EN 10028-71.4482 / X2CrMnNiMoN21-5-3 — comparison reference for the Chinese S22152 designation | Solution annealed (+AT); room temperature; H — hot-rolled strip/coil and sheett ≤10 mm | Rp0.2 ≥465 MPa for width <300 mm (longitudinal); ≥480 MPa for width ≥300 mm (transverse) | 660–900 MPa | A ≥30% for t ≥3 mm; A80 ≥30% for t <3 mm | Not specified in EN10028-7 Table10 |
| EN1.4482 reference limits only; a Chinese S22152 certificate does not itself establish EN10028-7 compliance. Original Table10. A uses L0=5.65√S0; A80 uses L0=80 mm, width20 mm (50 mm/12.5 mm specimen also permitted). Product-form/thickness scope is a standard limit, not a Sheye supply-range claim. Impact testing and other applicable order requirements remain relevant. | |||||
| EN 10028-71.4482 / X2CrMnNiMoN21-5-3 — comparison reference for the Chinese S22152 designation | Solution annealed (+AT); room temperature; P — hot-rolled platet ≤75 mm; no thin-product A80 value specified | Rp0.2 ≥435 MPa for width <300 mm (longitudinal); ≥450 MPa for width ≥300 mm (transverse) | 650–850 MPa | A ≥30% for t ≥3 mm; no A80 value specified for t <3 mm | Not specified in EN10028-7 Table10 |
| EN1.4482 reference limits only; a Chinese S22152 certificate does not itself establish EN10028-7 compliance. Original Table10. A uses L0=5.65√S0; A80 uses L0=80 mm, width20 mm (50 mm/12.5 mm specimen also permitted). Product-form/thickness scope is a standard limit, not a Sheye supply-range claim. Impact testing and other applicable order requirements remain relevant. | |||||
| ASTM A240/A240MUNS S32001 — related ASTM reference for Chinese S22152; requires independent compliance confirmation | Annealed flat product; room-temperature acceptance referenceNo grade-specific thickness split in the cited Table 2 row | ≥450 MPa (0.2% offset) | ≥620 MPa | ≥25% (50 mm or 2 in. gauge length) | ≤25 HRC |
| Room-temperature Table 2 reference; values are the printed SI limits. ASTM SI and inch-pound systems are independent. Yield uses 0.2% offset; Table 2 note B allows 0.5% total-extension-under-load unless otherwise specified. Elongation uses a 50 mm or 2 in. gauge length. Hardness alternatives and thin-material provisions follow Table 2 note C and A480. A480/A480M-22a §17.1.1: finished-material tension specimens may be longitudinal and/or transverse unless otherwise specified or agreed. Confirm the test direction in the contract and MTC. | |||||
| JIS G 4305No direct JIS counterpart verified | No confirmed mechanical limits for this reference. Review the exact order specification. | — | — | — | — |
| GB/T 3280022Cr21Mn5Ni2N / S22152 (Chinese designation, GB/T 3280-2015) | Solution-treated cold-rolled flat products; room temperatureCold-rolled only; A50 for t ≤3 mm; elongation and hardness reference only below 0.3 mm | ≥450 MPa (Rp0.2) | ≥620 MPa | ≥25% | HRC ≤25; no HBW limit listed |
| GB/T 3280-2015 Table 27. Select one suitable listed hardness method. These cold-rolled limits must not be used as hot-rolled coil, sheet or plate acceptance criteria. Test specimen and contractual requirements remain applicable. | |||||
ASTM A240 covers flat products; EN 10028-7 is for pressure-purpose flat products. JIS G4305 and GB/T 3280 cover cold-rolled flat products. Their cold-rolled values must not be used as acceptance limits for hot-rolled plate, bars or profiles. Confirm the standard edition and all supplementary requirements in the purchase order and mill test certificate.
Values are EN specification references, not automatic cross-standard equivalence, mill certification or universal as-hot-rolled guarantees. Width/direction-dependent yield minima are fully identified.
S22152 is a Chinese unified numerical code, not an EN name and not verified as a UNS code. Do not label this product UNS S22152. GB/T20878-2024 AnnexC TableC.1 row107 lists S22152 as the former number for current S20013 (022Cr20Mn5Ni2N); its prior name is022Cr21Mn5Ni2N. The foreign comparison lists S32001 and EN1.4482. The numeric EN data on this page describe the compared EN1.4482 grade. They are not a statement that every historic or domestic enterprise S22152 material meets all EN requirements. S22152 is a Chinese purchasing designation. Its EN 1.4482 comparison is shared with S32001; it does not identify a separate EN grade.
Chemistry is heat-analysis mass percent. Omitted elements have no requirement in the cited row, not zero. A480/A480M governs product-analysis tolerances and general requirements. Mechanical values use the printed SI column. ASTM regards SI and inch-pound systems as independent: do not convert ksi to generate an SI acceptance limit. Room-temperature Table 2 reference properties. Confirm delivery heat treatment, specimen preparation, dimensional tolerances and all general requirements against the contractual A480/A480M edition. Yield is based on 0.2% offset; a 0.5% total-extension-under-load alternative is permitted unless otherwise specified. Elongation gauge length is 50 mm or 2 in. HBW and the specified Rockwell scale are alternative permissible methods; thin-gauge superficial hardness provisions apply. The full 2026 numerical tables were not available for verification. Display the reference edition and confirm the contractual edition and certificate before accepting an order.
S22152 is a Chinese designation; it must not be labeled UNS S22152. No exact S22152 row was found in ASTM A240/A240M-20a. The linked primary research identifies Chinese S22152 as associated with UNS S32001; this supports a related reference, not automatic dual certification. The complete UNS S32001 reference is provided as a clearly labeled variant for technical comparison. For an ASTM order, specify UNS S32001 and verify the complete chemistry, mechanical properties, delivery condition and contractual edition. No S22152-specific ASTM numeric limits are invented or inferred from the UNS number.
UNS S32001 — related ASTM reference for Chinese S22152; requires independent compliance confirmation: This variant gives the actual ASTM UNS S32001 row for comparison. It does not create an ASTM or UNS designation S22152. Heat-analysis mass percent from ASTM A240/A240M-20a Table 1. Omitted elements are not zero-content requirements; product-analysis tolerances are governed separately. ASTM A240/A240M-26 is the current official catalogue edition. These are explicitly 20a reference values; the complete 2026 numeric tables were not directly verified. Hot-rolled coil/sheet/plate must still meet the specified annealed delivery condition, surface, dimensions and inspection requirements. These tables do not establish Sheye production dimensions. No numeric grain-size grade or fixed ferrite/austenite percentage is specified for this grade in the cited A240 rows. Agree any microstructure or phase-balance acceptance criteria separately; do not impose the austenitic H-grade grain rule on duplex material. A480/A480M-22a §18.3 requires A923/A1084 testing only when ordered, with grade applicability to be checked. Do not claim that every heat has passed an intermetallic-phase test without a certificate. ASTM Table 1 printed p.4 and Table 2 printed p.8. The row provides a Rockwell C maximum only; no HBW maximum is specified. Do not backfill a calculated Brinell limit. Annealing reference: A480/A480M-22a Table A1.2 minimum 1040°C, water quench or rapid cooling by other means; confirm the contract's incorporated edition. S32001 is different from S32003 and S32101. In particular, do not import an S32003/2003 product datasheet, the higher S32101 nitrogen band or a supplier's narrower nickel target as this ASTM limit. The Chinese designation S22152 is associated with S32001 in the cited primary research paper; cross-reference naming alone does not certify compliance with both standards.
JSA confirms the 2021 edition remains valid and was reaffirmed on 20 October 2025. Full purchased normative tables and all footnotes were not available for a complete current-edition audit. Listed chemistry is mass percent from primary JIS-grade summaries, not typical mill analysis. Missing cells mean not reproduced or not verified, not zero. Mechanical limits apply to the stated annealed/solution-treated cold-rolled condition at room temperature. Sampling, gauge length, direction, thickness-related rules and acceptance methods require the contractual standard. Corresponding designations are comparisons, not unconditional equivalence or proof that every supplied heat meets all listed standards.
S22152 is a Chinese numerical designation related to UNS S32001 in GB/T 3280-2015; it is not a verified Japanese designation or a separately established UNS number. This means the direct correspondence is unverified, not a claim that no contractual Japanese specification can ever be agreed. JIS G4305 covers cold-rolled flat products. JIS G4304 is the separate hot-rolled flat-product standard; its scope alone does not establish grade coverage or numerical acceptance limits. Do not relabel SUS821L1, SUS323L or SUS329J3L as this grade merely because each is a duplex stainless steel.
Chemical composition is heat analysis, mass percent, from GB/T 3280-2015. The corresponding designation is a reference, not automatic cross-standard certification. The requested Sheye product is hot-rolled coil, sheet or plate. GB/T 3280 is a cold-rolled comparison only; confirm a hot-rolled order against GB/T 4237 or the other agreed hot-rolled product specification, including delivery condition and thickness-dependent tests. These standard reference properties do not state Sheye inventory, production dimensions, typical heat analysis or guaranteed cross-certification. S22152 is a Chinese unified numerical designation in the 2015 GB product standards; do not write UNS S22152. GB/T 3280-2015 Annex A compares it with the American designation S32001. Naming update: China Elevator Association standard T/CEA 0053-2024, Table 1 note a, identifies S20013 / 022Cr20Mn5Ni2N as the revised GB/T 20878 name for the older S22152 / 022Cr21Mn5Ni2N used by the 2015 GB product standards. The chemistry and mechanical limits displayed here remain those of GB/T 3280-2015; they have not been silently replaced by the newer association standard. S22152 is the Chinese purchasing designation related to S32001 in the GB reference; it does not identify a second UNS grade.
Reference review: 9 September 2026 · Sheye Metal
SHEYE SUPPLY
S22152 is a Chinese unified numerical designation used for lean duplex stainless steel. For hot-rolled coil, sheet and plate enquiries, retain the exact grade description from the project specification or existing material certificate. This helps distinguish a legacy standard requirement from a current catalogue name or a steelmaker’s product designation.
GB/T 20878-2024 lists S22152 as the former numerical code for S20013. The current full designation is 022Cr20Mn5Ni2N; the former name is 022Cr21Mn5Ni2N. A change in catalogue naming should be checked alongside the product standard and edition required for the actual order.
The Chinese grade catalogue provides a comparison with UNS S32001 and EN 1.4482 / X2CrMnNiMoN21-5-3. These references assist material selection, but they do not automatically establish compliance with every specification.
For a project that requires both a Chinese grade and an ASTM or EN specification, ask for confirmation against the permitted chemistry, delivery condition and required tests. S22152 should not be written as “UNS S22152”. The supplied certificate must identify the agreed material rather than rely on a commercial cross-reference alone.
Provide thickness, width, quantity and the required form: coil, sheets cut from coil or plate. Include cut lengths and flatness requirements for flat pieces, or coil weight and handling requirements for coils. Surface finish, edge condition and any subsequent slitting or cutting should be agreed before processing.
Published standard limits and steelmaker datasheet values have different roles. Use the applicable product specification for order acceptance; use typical datasheet information to support an initial technical discussion.
Describe the component’s environment and intended forming, welding or surface treatment. Where replacing a previously supplied material, include the previous certificate and relevant drawing requirements. State the inspection document, heat identification and packing information needed by your receiving team. This gives the enquiry a consistent basis from material selection through processing and final document review.
LET'S TALK ABOUT YOUR NEXT ORDER
May we use optional analytics cookies to understand visits and improve our website? You can use our website and send inquiries either way.
With your permission, Google Analytics measures pages viewed, approximate visitor regions and inquiry, email and WhatsApp link interactions. It uses first-party cookies that identify a browser. We do not send your inquiry content, name, email address or phone number to Analytics. Google may process analytics data outside your country. Our analytics cookies expire within 6 months; your choice is remembered for 6 months. Withdraw permission any time using Privacy choices. This stops future collection and clears our analytics cookies.
